About this project
Published

Time
Time:0h00
Difficulty
So so
Crafts
Molding

Posted By

New York, New York, US
2008
Rubber Stamps
Please check out my website »
Create your own rubber stamps!

Learn how to create rubber stamps on any budget, inspired by any image or pattern you like.



Instructions

  • How to make a stamper. Rubber Stamps - Step 1
    Step 1

    The great thing about making rubber stamps is that you can make them cheaply, out of items you probably have lying around: an exacto knife (pictured left) and a rubbery eraser.

    As you get more detailed with your stamps, you may want to invest in a carving tool, like the Speedball brand shown. These are available at most art and craft stores, often with the lino cutting supplies.

    As your stamps get bigger, you'll also want to buy some carving material. My favourite is the pink "Speedy-Stamp" made by Speedball. It's a little more expensive than the beige material shown (about $5 for a postcard-sized sheet), but is less likely to crumble.

  • How to make a stamper. Rubber Stamps - Step 2
    Step 2

    If your stamp design is pretty simple, you can draw directly onto the rubber. Otherwise, it's best to draw your design onto a piece of paper first, remembering that WHAT YOU DRAW WILL BE REVERSED ON THE STAMP. Important to remember if you're carving text!

    In this case, I was making a stamp for a friend based on one of his illustrations. I took the image into Photoshop, resized and lightened it. Next, I used a soft pencil to go over all the places I want to print in the final stamp.

  • How to make a stamper. Rubber Stamps - Step 3
    Step 3

    Now place the image down on the stamping rubber, and affix in place with a small piece of tape. Transfer the image to the rubber by shading over the back of the illustration, or rubbing it with the back of a spoon.

    Another technique, if you're using a photocopy, is to apply a small amount of acetone (nail polish remover) to the back of the paper. This does NOT work, however, with images printed by inkjet printers. (I learned that the hard/messy way!)

  • How to make a stamper. Rubber Stamps - Step 4
    Step 4

    Remove the paper, and your image should be transferred! If the image isn't clear, try using a softer pencil.

    At this point it's a good idea to roughly cut the stamp out of the rubber sheet so that you can rotate the rubber easily as you carve.

  • How to make a stamper. Rubber Stamps - Step 5
    Step 5

    I like to start with the outlines of all sections. Run the carving tool away from you without pressing too hard or you'll end up gouging the rubber and taking out a chunk you don't want to. Remember that you can always take away more rubber later, so err on the side of taking less away.

    When carving along curving lines it's best to keep the tool in one place and rotate the rubber.

    If you're having trouble seeing where you have or haven't carved, try coating the whole piece of rubber with a thin layer of ink.

  • How to make a stamper. Rubber Stamps - Step 6
    Step 6

    Once you've finished carving (remembering that the pieces you leave uncarved will appear in the final stamp), use your knife to cut away excess rubber around the edges.

  • How to make a stamper. Rubber Stamps - Step 7
    Step 7

    Time for a test stamp (lower left) to check how you're doing. On the lower right you'll see the final version after some extra pieces were carved away.

    And...you're done! Don't worry if there are a few wonky bits, it adds to the charm of hand-carved stamps :)

  • How to make a stamper. Rubber Stamps - Step 8
    Step 8

    There are tons of designs you can use to make your stamps.

    Whereas the stamp above is an outline of an image, this one is solid, inspired by a logo I saw on the back of an envelope.

  • How to make a stamper. Rubber Stamps - Step 9
    Step 9

    You can also use a photo as the basis for your stamp, like this one.

Have you made this project? Add your version
And you're done!

Recent Versions


Rubber Stamps

Rubber Stamps

♥ 2

Comments

ronit s.
ronit s.
hi my name ronit I WANT TO ASK 1. WERE IN THE INTRTNET I CAN BAY THE PINK RUBBER?
Reply
KattyRa
KattyRa · Iași, Iași County, RO · 4 projects
Soo great idea!!
Reply
Alessandra S.
Alessandra S. · New York, New York, US
loveit. i also tried a simon&garfunkle stamp, but used printmaking supplies and used white printink on black paper. *tries to find camera to post 'my version'*
Reply
Grace D
Grace D · London, GB · 83 projects
Thats wickeeddd, I'm going to make one with my name and the little star and heart and stamp it on all my makes
Grace★♥
Reply
Jeanette
Jeanette · Milwaukee, Wisconsin, US · 1 project
meh pay that no mind i love the tutorial and idea and the face is hawt! :3
Reply
Markie
Markie · Glasgow, Scotland, GB · 1 project
oooo....great tutorial. i would have never known to make such a thing. thanks!
Reply
Alex F.
Alex F. · Richmond, Virginia, US · 1 project
Oh gosh, we spent so many weeks doing a few of these in art in high school. I don't think I was very good at it but I still display the finished prints I made Happy
Reply
Myam
Myam · Cebu City, Central Visayas, PH · 18 projects
i will make some for my tags. Happy thanks for the inspiration
Reply
northernstar
northernstar · Flateyri, Westfjords, IS · 35 projects
This is so interesting! I love stamps and have always wanted to make my own.
Great tutorial and I love the tree stamp!
Reply
· Coeur d'Alene, Idaho, US · 23 projects
Wow! So cool! Thanks for sharing.
Reply
Load 2 more comments...

Recent Favorites


Kimya J.
Keith	 N.
Spencer M.
arina m.
cristinakilljoyway
HiroLover
rhayne_
Devin O.
eden a.
Lori H.
Kendra L.
Lina N.
Julie S.
pauline
Treneice H.
Jessica G.
Perelin18
Jamie

Similar projects

Loading...