About

Cost
$ $ $ $ $
Difficulty
• • • • •
Time
2h00

Wire bracelets diy-a personalized jewelry for mothers
Make a great craft project to help remind you of the impressive and engraved Mother’s Day. The wire bracelets diy items may be one most versatile and personalized jewelry for mothers.

Published
Tags

PrintEmbed

You Will Need

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 1
    Step 1

    Supplies needed in wire bracelets diy:

    10mm Faceted-round Glass Bead

    8mm Abacus Glass Bead

    S-hook Clasp

    2mm Aluminum wire

    0.5mm Brass Wire

    Stick

    Flat Nose Plier

    Round Nose Plier

    Side-cutting Plier

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 2
    Step 2

    Step1: loop out the frame

    1. Cut a certain long strand of 2mm aluminum wire. Reserve about 5cm long at one end, and then form your first loop around the cylindrical stick in clock-wise direction;

    2. Take the loop off the stick;

    3. Hold the tail and form more adjacent loops in same directions;

    4. Measure your wrist circumference and determine the loop portion about 5cm less than it.

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 3
    Step 3

    Step2: wrap on the central focal beads

    1. Prepare another fairly long strip of 0.5mm brass wire, and then affix the beginning at the first link by several coils;

    2. Slide on one 10mm bead;

    3. Secure the bead in place by another turns of wire;

    4. Keep going until finish each loop;

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 4
    Step 4

    5. Leave another 5cm long at end and remove excess tail;

    6. Curve the strand into a circle around something similar to human wrist size;

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 5
    Step 5

    7. Take it off the assistive tool and this is your semi-finished wire bracelet.

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 6
    Step 6

    Step3: adorn the blank on edges

    1. Take another strip of 0.5mm brass wire and wrap the two edges on your bracelet.

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 7
    Step 7

    Each time came across the blank fill it with an 8mm abacus bead;

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 8
    Step 8

    2. Do repeat the same processes for another side;

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 9
    Step 9

    3. When both sides are done, you will gain the below vision.

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 10
    Step 10

    Step4: design a natural closure for the wire bracelets diy project

    1. Back to the remaining 5cm wire at both ends, loop either of them and wrap the tails around its neck;

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 11
    Step 11

    2. To the other one, before looping the wire you should slide on the clasp.

  • How to make a wire bracelet. Wire Bracelets Diy A Personalized Jewelry For Mothers  - Step 12
    Step 12

    3. Pack your personalized jewelry for mothers and make her a huge surprise.

    Thus far, the entire wire bracelets diy processes may be ceased here. However, as a personalized jewelry for mothers, you can certainly replace the decorative beads in this post with somewhat significant objects such as the meaningful birthstone of family. Mom will love receiving this gift from her children so much.

Made this project? Share your version »

Comments