Cute earrings that look like spiders hanging from a web!
These spider web earrings are a fun and easy to put together. They are perfect to wear on Halloween night or to give away as a gift.
- Key West Witch added Spider Web Earrings to Jewelry 30 Jun 07:59
- Kaitlynn L. favorited Spider Web Earrings 20 Aug 14:31
- Vi F. favorited Spider Web Earrings 16 Oct 04:19
- Jennie I. added Spider Web Earrings to Addams Ladies 05 Oct 14:15
- Rhiannon R. added Spider Web Earrings to Jewlery 09 Apr 04:04
- Rhiannon R. favorited Spider Web Earrings 09 Apr 04:04
- meligg13 favorited Spider Web Earrings 18 Sep 04:20
- caitlinannabella favorited Spider Web Earrings 29 May 15:52
- FrankieStein favorited Spider Web Earrings 16 Feb 07:09
- nina.eriksen.90834 added Spider Web Earrings to To-make 02 Dec 15:11
Begin the spider web earrings by opening up the wine charm rings. Thread on black seed beads all the way around the ring. At the end, add on a jump ring. Then, close up the wine charm ring. The charm rings I bought required you to bend up the one end of the loop slightly with jewelry pliers and insert it into a tiny hole on the other end to secure.
Next, cut off about one foot of embroidery floss and unravel it until you have single strands. Thread a single strand of black floss through your needle. Then, wrap this thread around the loop ring, in between two of the seed beads. Tie a knot to secure the thread, and cut off the excess as close as you can to the loop ring.
Begin to make the spider web by pulling the thread across the ring loop, in various patterns. Try not to always go directly across the middle, or the spider web will look too "perfect". When the thread reaches the other side, wrap it between the seed beads, and around once to secure. The seed beads keep the floss in place nicely. When you are finished threading, tie the the floss off in a knot between two seed beads, and cut off the excess and close as you can to the ring loop to make it look nice and neat.
The next step for the spider web earrings is optional, but I really recommend it. Give the front and back of the spider web loop earring a coat of silver glitter spray paint. Let it dry between doing the front and back sides. It really gives it some extra sparkle!
Now to finish off the spider web earrings you need to make the spider. First, gather up your parts. The two pom poms will be the spider's body. Cut a tiny piece of black card stock in a small rectangle. You can see the small rectangle in the photo below, to the far left. You don't want the length to be any longer than the width of the two pom pom's side by side (in my case, slightly smaller than 1 cm). The card stock's purpose is to be the base of the spider to glue the parts to, but you don't want to see it in the final product. Then, using your tweezers or jewelry pliers, pry off four staples from a length of standard staples you would load into your desk stapler. These will be the legs.
Make your spider on top of a sheet of wax paper or parchment paper, so it the glue oozes, you can carefully peel him off safely. Begin by adding a drop of glue to the card stock. You may want to use tweezers here to hold down the tiny card stock so it doesn't stick to your glue tip! Then, glue on two staples across this card stock, in an "x" pattern, as shown below. Use your tweezers to help place the staples.
Add another drop of glue on top of all the staples, and then place the two black pom poms on top of everything to be the spider's body. Use your tweezers for help. Allow this to dry very well. When dry, you can use the head of a pin or a toothpick, dipped in some white paint, to add two tiny eyes, if desired.
When you are sure the spider is nice and dry, thread your needle with another length of one ply black embroidery floss. At the top of the spider's head, insert your needle through the head width wise. Try to get deep enough in the pom pom so the thread will be secure and will not pull out. Then pull your thread through, and make a knot. Cut off the trailing end of the floss as close as possible to the spider's head.
To attach the spider to the spider web earrings, wrap the floss around the bottom of the loop, in between two seed beads. Determine how far you want the spider to dangle from the loop and adjust the floss length as necessary (for my earrings the spider hangs 1 cm below the loop). Once the length is determined, secure this by wrapping the thread around the ring loop one more time (in between the seed beads again) to secure it well, then bring the thread back down towards the spider. As you bring the tread back down to the spider, wrap it around the floss a few times. This is done to make it look like only one thread holding the spider instead of two.