Top Hat Band Ribbons And Giant Kanzashi

My first hat band for my top hat.

Posted by Mildred C.

About

I had funky aisan-esque fabric that I was using for my outfit (in fact, I have more and will make a bodice or waistcoat in the future...). So I got ribbons in the various colors of that fabric and the teal/hawaian blue of my skirt and made this hatband.

I had been at a con just before that with a vendor who sold "kanzashi" (in reality just decorated combs and hair clips). In searching google, I came across an awesome tutorial at http://www.mookychick.co.uk/diy_ethic/kanzashi_tutorial.php and some youtube videos.

I did this all with hand sewing, so that's why it took so long.

Note- I made this before I joined, so most of the how to are ones that I made afterwards to show the steps.

More pics to come.

Share

You Will Need (7 things)

  • 1 x Needle
  • 1 x Thread neutral color for the ribbons you chose
  • 1 x Gears
  • ½ yd square of Brocade Fabric
  • 1 Top Hat
  • Satin Ribbon various widths and colors
  • 1 x Watch face

Steps (11 steps, 60 minutes)

  1. 1

    Measure around the base of the hat (not the brim, but the base that goes around your head.

  2. 2

    I'm not positive on the widths, but had 4 widths of ribbon. The widest was gray, next widest was yellow, then electric teal, and the smallest were a set of thin ribbons in royal blue, red, and lime green.

    I took the three widest ribbons and measured out the length of the measurement in Step one, and added a seam allowance (I did a french seam), and cut. More on the thin ribbons in a moment.

  3. 3

    I pinned the yellow ribbon onto the gray so that the yellow ribbon was in the middle of the width of the gray.

    I then pinned the electric teal ribbon onto the yellow, again so that the teal was in the middle.

    I then hand sewed the teal and yellow ribbons down along their edges, so they wouldn't flap up.

  4. 4

    I then took the royal blue, lime green, and red ribbons (which were the same size), and braided them together until I had a piece the same length of the hat band in process.

    Then I sewed that down the middle of the electric teal ribbon.

  5. 5

    I then folded right sides together and sewed down the seam allowance. I did a french seam so the ribbons wouldn't fray.

  6. 6

    I then used the awesome tutorial at http://www.mookychick.co.uk/diy_ethic/kanzashi_tutorial.php to create a large sized kanzashi (but didn't make a center for it) from the brocade fabric.

  7. 7

    I created a base for the kanzashi with some scrap fabric of the skirt that this hat band was going with (to let it rest a little away from the actual hat). I just took a long strip and wrapped around into a solid cylinder.

    I then sewed the kanzashi to one side of the base.

  8. 8

    I had a gear with a post, and the post fit through the center of the large watch face. So I put the gear into the watch face and pushed the rest of the post into the base, through the center of the kanzashi.

    Then I used some embroidery thread to stabilize the gear.

  9. 9

    I didn't use the gray ribbon any more, but I used all the other ribbons mentioned before plus some others (silver and gold organza, other colors in the same colors as the inspiration fabric ), and cut random long lengths.

    I then folded them in half and sewed them onto the other side of the base of the kanzashi.

    See this pic for a layout after Steps 8 & 9.

  10. 10

    I then sewed the kanzashi piece to the hat band, at the seam. I ended up placing another ribbon around the seam to strengthen it against the weight of the kanzashi.

  11. 11

    The hat band is just loose enough I can place the kanzashi at almost any point along the hat and just drape the ribbons aound the hat. I usually place it to one side or mostly to the back, but never in the front.