https://www.cutoutandkeep.net/projects/the-red-dragon • Posted by Miss Sixty
Yo might want to know that creating this dragon is very complicated and you have to be very careful to understand. I was taught to make this dragon by my aunt and now I share it with you! I hope you manage to get it well ...
Yo might want to know that creating this dragon is very complicated and you have to be very careful to understand. I was taught to make this dragon by my aunt and now I share it with you! I hope you manage to get it well ...
This is what you will need. You should really use origami paper because the model is very complicated and xerox paper won't do. I made my dragons with xerox paper but I made them a few times to get them right because the paper is to rough.
Fold your paper equally on the long side of the paper.
You get this. Now you need to fold it again into half.
You will get a rectangle which will be cut into half.
Now you have a triangle. It should look like this.
Open it.
You get a square folded across the diagonals.
Now you fold it into half exactly like in the picture.
You get this triangle. Now you have to fold the corners inside the model, guiding yourself by the vertical center.
You get this.
Turn over the sides on the front and on the back as well.
This is how your model should look like.
Now fold the sides according to the vertical center.
Like this.
Now fold the triangle that has been left according to the upper sides.
Open the 3 folded parts and get this.
Now you pull that thing down like in the picture.
Now your model looks like this.
Do the steps 13-18 for the back as well and get this.
Now fold the right side like this. Do this on both sides.
Now grab the upper side and fold it over according to the center. Do this on both sides.
You get this.
Now you cut down the right part like in the picture.
It should look like this.
Now grab the left side and pull it over. Do this on both sides.
This is how it should look.
Now you'll want to fold both parts according to the vertical center. Do this on both sides.
Now cut two little diagonal openings on both folded sides on this part.
Here is a closer look to get it right.
Fold up the upper cuts than turn the model.
Make two little cuts on this side as well like in the picture than fold in half the entire model.
You should have this.
Back fold half of the model and you form the neck of the dragon.
Back fold again the part on top of the thorn.
Reverse fold in that area.
With a reverse fold you get the feet of the dragon. Do this on both sides.
Fold the feet in half.
Back fold the feet and the beak.
Reverse fold the feet.
Back fold feet.
And finally, fold up the ends making the talon. The feet are ready.
Your beak should look something like this. Find the cuts you previously made and try to pull them out. These are smaller thorns.
After you found the thorns, you have to pull out the upper part of the beak just like in the picture.
Cut it in making a thorn on both sides.
This is how the head should look at the moment.
Now grab the upper part of the beak and fold it back.
Back fold the beak.
Revers fold the beak. This is the mouth.
Finally, fold down the end of the beak. This is the tongue.
Now, with a back fold and a reverse fold you make the ears.
Cut in between them and part them.
Now fold up the ends.
The first part of your dragon is ready!
Use the other A4 paper and repeat steps 2-26. Take the right part and fold it over to the left.
It should look like this.
Now fold the entire model into half.
Hold the model like this.
Cut it in 4 spots.
Now fold them up making some little thorns.
Take the right part and turn it on the left side. Repeat steps 57-59.
Form the right side like this and fold it into half.
It should look like this. These are going to be the feet.
Now open the model.
Fold in the sides according to the feet.
Now fold the model into half.
Cut down the right end.
The the other end and cut it in on the sides. After that, pull them out.
You have here the tale of your dragon ;)
open the feet and cut them like in the picture. After that fold them over.
Reverse fold the feet.
Back fold.
Reverse fold.
And finally, fold up the ends for the talon.
The second part of the dragon is ready!
Now put the two parts together.
Use the Stapling Machine to make them stay that way and model your dragon the way you like.
Ready!