About

Cost
$ $ $ $ $
Difficulty
• • • • •
Time
1h00

Glass, pendant, razor blade, goth, jewelry, Glassprimitif, Etsy,
Create this simple, yet unusual, razor blade pendant using glass, a blade, copper foil and a soldering iron. You can customise your pendant by including red enamel powder or, for coke-heads, white enamel powder.
This pendant will make heads turn - every goth and emo should own one!

Posted by Glassprimitif Published See Glassprimitif's 4 projects »
Tags

PrintEmbed
  • How to make a recycled necklace. Razor Blade Pendant - Step 1
    Step 1

    You will need two pieces of thin picture glass measuring 2" x 1 1/4" and a new razor blade. Wash both pieces of glass carefully in hot, soapy water and then rinse in hot vinegar water to clean off any grease. Dry thoroughly with a clean towel.

  • How to make a recycled necklace. Razor Blade Pendant - Step 2
    Step 2

    Place the blade between the two pieces of glass. Avoid handling the glass at the edges as your fingers are naturally greasy. Peel back the paper from the copper foil (I have used 1/2" foil) and wrap the edges of the glass to make a "sandwich". Overlap the foil when you reach the end.

  • How to make a recycled necklace. Razor Blade Pendant - Step 3
    Step 3

    Smooth the foil down with your finger nail or the back of a spoon on both sides of the glass.

  • How to make a recycled necklace. Razor Blade Pendant - Step 4
    Step 4

    Plug in your soldering iron and, as it heats up, take a soft paintbrush and dip it onto the liquid flux. Paint all the copper foil with the flux, including the sides. (Without flux, your solder won't stick to the copper foil).

  • How to make a recycled necklace. Razor Blade Pendant - Step 5
    Step 5

    Pick up the heated soldering iron and touch it to a small piece of led free solder. Using the tip of the iron, run the solder along the edges of the copper foil, coating it completely.

  • How to make a recycled necklace. Razor Blade Pendant - Step 6
    Step 6

    Close up image of the soldering iron and pendant.

  • How to make a recycled necklace. Razor Blade Pendant - Step 7
    Step 7

    Make a loop to hang the pendant. Using jeweler's pliers, wrap a thin piece of copper wire around a paint brush to form a loop. Now bend the wire to wrap the loop and cut to size with the jeweler's cutters.

  • How to make a recycled necklace. Razor Blade Pendant - Step 8
    Step 8

    Paint the copper loop with flux and solder it to the top of the pendant. (As copper and glass conduct heat it is advisable to hold the glass between pliers ot tongs).

  • How to make a recycled necklace. Razor Blade Pendant - Step 9
    Step 9

    Wash your pendant carefully with a damp sponge to remove any grease, taking care not to overwet it. Now pop it on a chain or cord and wear it immediately!

    If you want to purchase this exact pendant just go to:
    http://glassprimitif.etsy.com

Made this project? Share your version »

Comments

DarkAshHurts
DarkAshHurts · 119 projects
Lmao, Coke-heads. XD
I wish i knew how to solder, id def make this!
Reply
* **Me_no_RazOr** *.
* **Me_no_RazOr** *. · U.S. Air Force Academy, Colorado, US
Nice haha
Reply
KieraMD
KieraMD · London, GB · 6 projects
I Soo Wannahh Make This
Mum Might Become A Bit Worried Though ¬_¬
Still, It Rocks!
Reply
Anitaxx H.
Anitaxx H. · 2 projects
U ROCKZZ!
Reply
Frankie
Frankie
break glass in case of an emergency...lol. this looks really cool!
Reply
QueenQuill
QueenQuill
So hawt! I want one!
Reply
Cat Morley
Cat Morley · London, GB · 1372 projects
Sorry about that, it's fixed now!
Reply
Glassprimitif
Glassprimitif · 4 projects
Where has the image of the pendant gone?
Reply
Lesley D.
Lesley D. · Birmingham, Alabama, US
I love this!! Way too cool!
Reply
LaKore
LaKore · Vinton, Virginia, US · 1 project
Oh I just love this how much does the flux cost?
Reply
Load 5 more comments...