About this project
Published

Time
Time:2h00
Difficulty
So so

You Will Need


Cost
Cheap
Crafts
ConstructionWoodwork

Posted By

Marquette, Michigan, US
2008
Jewelry Display Rack
Handmade Earring Display Racks
Jewelry Display Rack from Hardware Store Parts

<b>Example 1: Wooden Dowels and Copper Pipe Fittings</b>

One fun and easy way to create your own jewelry display racks is by using copper pipe fittings and dowels. All hardware stores seem to have these supplies. Be creative with the parts, it is like using legos. I usually find the type of fittings that are in my price range, and then find a dowel that will fit into them. The copper pipe fittings have T shapes and L shapes so the best way to get the display you want is to sketch it out first then buy the fittings and dowels. One advantage to this display is that it breaks down easily if you are traveling or don’t have a lot of space to store things.

I would suggest adding in eye hooks where you can thread through smaller dowels to individually hang earrings or earring cards. If you have trouble getting your new rack to stay rigid, hammer the copper pipe fittings while they are on the end of the dowel. Be careful not to hammer too much so you are still able to take it apart. To hammer the copper fitting, just put it on a solid surface and hit it with a hammer or a mallet in order to pinch the dowel.

Cutting the dowels into the proper lengths is not too difficult with a hack saw, or any hand saw. Since the ends on most of the dowels will be covered by the copper fittings, the cuts don’t have to look amazing. They also make end pieces of copper that could be stuck on the end of a dowel. As you can see in the example above, I did not use any end pieces, only connectors. I just used a little sand paper on the ends to make them look smooth. If you are really good at planning out the cutting of the dowels, you could keep the factory ends of the dowel for any ending that is going to be showing.

<b>Example 2: PVC Pipe Jewelry Display Rack (The Cheaper Version)</b>

I also think this design would work with small PVC pipe fittings and pieces of PVC pipe, then the entire rack could be painted afterwards. It would look really nice with a metallic finish spray paint over the surface. Or you could use dowels and PVC Pipe Fittings. The most fun part is doing it yourself with relatively inexpensive materials. Also, potential customers are drawn to interesting displays, but you don’t overdo it. You don’t want the display to compete with your jewelry.

<b>Example 3: Copper Pipes and Copper Pipe Fittings (The More Expensive Version)</b>

I think an entirely copper display would look really awesome, but the price of copper is more than it used to be, so this display is an investment. But it would look really great if you are a fan of copper. Copper is also able to be cut with a hacksaw, just have a friend help you hold down the copper pipe so you can cut in a straight line.

<b>Helpful Hints:</b>

Definitely sketch out a detailed drawing with measurements of the rack before cutting up a bunch of dowels. Better Yet, make your drawing before you go to the hardware store and then you won’t have a bunch of extra pieces.

Find a friend to help. I assume you all have a few friends or significant others that can help you hold the pieces of dowel while you are sawing. If you can’t find anyone to help, you can also use a vise to hold the other end of the dowel. Use two pieces of scrap wood on the jaws of the vise so it doesn’t dent you dowels.

Remember that dowels generally come in 1 yd lengths. Example: if you need four 16″ lengths, you are going to have to buy three dowels. There will also be some leftovers, of each of the three pieces.

If you are planning on hanging earring cards that have plastic hangers, make sure they fit over the dowels.

To brighten the copper pipe fittings they can be scoured with baking soda or ‘bar keepers friend’ and steel wool. This is also a good way to remove adhesive on the surface of the copper.

PVC Pipes usually have numbers on the side so I would seriously consider painting them. You could probably come close the the all copper look with some copper spray paint.

There is also glue available that is especially for PVC Pipe, it will be near it where ever it is sold. Beware the glue smells really bad, use in a ventilated area.

Jewelry Organizer

Jewelry Organizer

jewelry organizer

♥ 12
Ikea Stave To Jewelry Display

Ikea Stave To Jewelry Display

STAVE-Mirror to Jewelry Display.

♥ 5
Wall Jewelry Display

Wall Jewelry Display

wall jewelry display

♥ 10
Diy Jewelry Hanger

Diy Jewelry Hanger

Easy DIY Jewelry Hanger

♥ 1
Jewelry Hanger

Jewelry Hanger

A place for that lonely jewelry to hang.

♥ 7
How To Make A Jewelry And Trinket Stand With A Faux Patina

How To Make A Jewelry And Trinket Stand With A Faux Patina

I couldn't just leave my bracelets laying around, so I made a quick bracelet and trinket stand. So, today I'm going to show you how to build ones of these, and also do a Faux Patina.

♥ 3

Comments

Dee S.
Dee S. · London, GB · 41 projects
You are so smart, keep the ideas coming. Looks like I am going to be in DIY shops a lot.
Reply
Betty K.
Betty K. · New York, New York, US · 17 projects
This is perfect!!! I've been searching for an idea that would work to display my jewelry on my shelves and keep them easy to access!!! Awesome!!
Reply

Recent Favorites


Death or Plumbing!
Penny F.
Zombie Babe
Gloria B.
Anika E.
Tabitha H.
Jill T.
simone c.
ashley s.
gabriella
HannahMary
My Belle Bijoux
SLAP_art
fine409
Jaded R.
teighlor gray
Rebecca aaaahhh!
Betty K.

Similar projects

Loading...