Cut Out + Keep

Dr. Who Sweater Stenciled And Bleached

A customized sweater using bleach stencils and fabric paint!

https://www.cutoutandkeep.net/projects/dr-who-sweater-stenciled-and-bleached • Posted by LizzyLovesSatan

This was a christmas present for my boyfriend. The Doctor on the front and the Dalek on the sleeve are bleach stenciled, and the rest are done with fabric paints. All the stencils are made from contact paper. I worked on this while he was at work over the course of a few weeks; the fabric paint is time consuming because you need it to dry between layers, so I prefer the bleach!

You will need

Project Budget
Cheap

Time

12 h 00

Difficulty

Tricky
Medium 109452 2f2015 06 20 220349 sam 1505 Medium 109452 2f2015 06 20 220352 sam 1506 Medium 109452 2f2015 06 20 220354 sam 1507 Medium 109452 2f2015 06 20 220357 sam 1508 Medium 109452 2f2015 06 20 220400 sam 1509

Description

This was a christmas present for my boyfriend. The Doctor on the front and the Dalek on the sleeve are bleach stenciled, and the rest are done with fabric paints. All the stencils are made from contact paper. I worked on this while he was at work over the course of a few weeks; the fabric paint is time consuming because you need it to dry between layers, so I prefer the bleach!

Instructions

  1. First, find or create an image to use. For this method, make sure it is a proper stencil with bridges so that you are not left with free floating pieces in the design. For this weeping angel face, it was small enough to print on one sheet of paper.

  2. Next, cut a piece of contact paper big enough to fit your image on it, plus extra so that you don't risk painting on the sweater! Then you need to trace the image onto the clear side of the contact paper. I prefer to use a fine point permanent marker for this. No need to be SUPER exact; the cutting is what really matters here!

  3. Once your design is traced, use an x-acto knife to cut out the design, being careful not to cut any of your bridges off. Also be careful to cut out all the parts completely. It sucks to get done cutting only to found out a few tiny corners are still attached and you need to go back in with the knife!

  4. Small 109452 2f2015 06 20 221551 sam 1501

    Then just carefully peel the clear side of the contact paper off the paper side, and position it on the item you are going to stencil. Make sure everything is nice and flat, and that all the edges of the contact paper have made solid contact with your fabric.

  5. Small 109452 2f2015 06 20 221647 sam 1502

    Now, start painting! If your fabric is at all thin, put something behind the layer you are stenciling so that you won't risk paint bleeding through. Make sure to cover the image totally. I like to do between two and four layers of paint, depending on the fabric. Use your judgement! **Be sure to let each layer dry completely before you start another layer!

  6. Small 109452 2f2015 06 20 221739 sam 1503

    Do not do TOO MANY layers though: if fabric paint is too thick, it will start lifting off and crack easily. Again, use your best judgement. Once all the paint is totally dry, gently lift the stencil off. ** I can tell that I have used TOO MUCH paint if I have to run along the edges of the print with a knife to get the stencil off. I tend to use too much a lot :P

  7. Small 109452 2f2015 06 20 221932 sam 1500

    Here's another in-progress of the logo on the front. I mixed glow in the dark paint with this one :) ** If your fabric paint requires ironing, the time to do it is once you have the stencil off. Follow the instructions for your paint!

  8. Small 109452 2f2015 06 20 222032 drwho%2bdoctor%2b4

    I used this image for the back of the sweater. To get it big enough to cover the whole back, I used the program Posterazor (very basic program that works super well!).

  9. Small 109452 2f2015 06 20 222201 sam 1507

    The back - finished. This one also glows in the dark!!

  10. Small 109452 2f2015 06 20 222309 drwho%2bdoctor

    BLEACH STENCILS ~ These are basically the same as the fabric paint, the design is just reversed so that the image to be used is one solid piece, and the bleach goes all around it. Stick your stencil to the hoodie. Put a bit of bleach into a small spray bottle, and gently spray the area with bleach. Dab with a paper towel to get rid of excess bleach, and repeat the process as needed until the fabric reaches your desired lightness. This happens pretty quickly, so be prepared to work fast!

  11. Small 109452 2f2015 06 20 222437 drwho%2bdalek

    When working with bleach, always work in a ventilated area and wear gloves! For style, I like to set the spray bottle so that I can spritz very gentle and get a nice drizzle of bleach drops all over the design. This gives it a nice organic, drippy look!