About
For 1/6 scale dolls and the like!
My Obitsu boy needed a new shirt, so I got a brainstorm and some socks and made him one! This project should be fine for even beginners :)
-
joy.mardon.1 added Doll Sweater from Socks to Things for dolls
28 Jan 10:45
-
Key West Witch favorited Doll Sweater from Socks
10 Sep 09:30
-
Faerydae M. favorited Doll Sweater from Socks
03 Jun 06:12
-
Quackers, Vino & Cheese favorited Doll Sweater from Socks
12 Nov 19:22
-
Kay T. favorited Doll Sweater from Socks
11 Nov 08:02
-
Jennifer M. favorited Doll Sweater from Socks
28 Mar 19:30
-
Kara B. favorited Doll Sweater from Socks
19 Jan 03:42
-
Packye favorited Doll Sweater from Socks
26 Sep 16:58
-
Amanda T. added Doll Sweater from Socks to Sock creatures
21 Sep 23:22
-
Amanda T. favorited Doll Sweater from Socks
20 Sep 21:30
You Will Need
-
Step 1WHAT YOU WILL NEED:
2 Tube Socks
Scissors
Thread
Needle
Sewing Machine*optional* -
Step 21. If you are using large mens socks like I am, cut the tube at about 2/3 to the end of the tube part. If you are using smaller socks (such as womens), Just cut at the end of the tube. Do this for both socks.
-
Step 32. Step 1. completed.
-
Step 43. Now grab one of the tubes you cut. Make sure the cut end is pointing up, and the side you want the outside of the sweater to be is on the inside (you may have to turn the tube inside out). Now divide the tube in half (IN YOUR MIND), then in fourths (AGAIN, IN YOUR MIND). Sew along the outer fourths, starting about an inch down and sewing all the way to the edge. Make sure ONLY AN INCH IS SEWN and the rest of the tube is unsewn. You can either use a machine or hand sew (here I've hand sewn).
-
Step 54. Step 3. Complete.
-
Step 65. 3. from the inside top edge. The bottom should have no divisions.
-
Step 76. Now grab those scissors! Cut a curved section starting about two inches down and a little before than the line you've sewn. BE CAREFUL NOT TO CUT OVER WHERE YOU'VE SEWN! The end result should have a hole that stops where the stitches start. Now set this part aside...
-
Step 87. ...And grab the other tube! Divide the tube in half (yet again, in your mind).
-
Step 98. But this time, cut along the line! AKA just cut the tube in half.
-
Step 109. Now take one of the pieces you've just cut and, with the side you want the sweater to be on the inside, sew the edge closed. Start from the cut edge and sew about 1/4 of an inch up. Sew all the way to the other end. Repeat on the other piece. You may use a machine if you want.
-
Step 1110. Once both the pieces are sewn, turn them inside out! Here's one of the pieces in the process.
-
Step 1211. Step 10. completed on both pieces. Now grab the very first part (the one from the other tube), as well as one of the long pieces that was turned inside out...
-
Step 1312. ...And stuff one of the long pieces into the big one, pulling it up through the hole! In the process.
-
Step 1413. Step 12. complete. Now sew the long piece (the sleeve) to the big one (the body) by sewing around the edge of the hole. Be careful not to sew the sleeve shut! I recommend you hand sew this part, 'cause I don't know of any machine small enough to do this detail! Then pull up the other sleeve on the other side and do the same.
-
Step 1514. Step 13. completed on both sides. Now, the fun part!
-
Step 1615. Turn the main body inside out, roll the sleeves up and the neck down (if desired)...
-
Step 1716. And you have a sweater! Now to go try it on my boy.
-
Step 18Ta-da! Hope that was a good tutorial!
CO + K User