https://www.cutoutandkeep.net/projects/cigar-box-books • Posted by GMC Group
The pampered lifestyle of kings and queens is lost to most of us, but you can re-create it with hand-sewn books. This set of mini journals may strike your fancy or serve as an honorable gift to the royal persona in your life. finished dimensions Depends upon the original box size stitches used Coptic stitch - http://www.cutoutandkeep.net/projects/coptic-stitch running stitch, gathering stitch - http://www.cutoutandkeep.net/projects/gathering-stitch
The pampered lifestyle of kings and queens is lost to most of us, but you can re-create it with hand-sewn books. This set of mini journals may strike your fancy or serve as an honorable gift to the royal persona in your life. finished dimensions Depends upon the original box size stitches used Coptic stitch - http://www.cutoutandkeep.net/projects/coptic-stitch running stitch, gathering stitch - http://www.cutoutandkeep.net/projects/gathering-stitch
Cut the lid off the cardboard cigar box by gently running a craft knife along the inside hinge of the top panel and repeating until all layers of the cardboard are cut. Working from the inside of the cardboard cigar box, gently cut through the layers of board at all side joints (where the side panels meet each other in the corners). Cut the remaining joints that link the side panels to the bottom panel of the box. Once that’s done, you will have six individual boards.
With a paper cutter, even out the raw edges of the boards so they’re straight.
Smooth the cut edges of the boards by lightly sanding them with fine sandpaper. Depending upon the age of your cigar box, some of the printed label paper may flake off. This is okay—it adds to the vintage look.
Cover your worktable with wax or craft paper to protect it from the ink. With a brush and undiluted India ink, paint the raw edges of the boards with one or two coats. Allow the edges to dry completely.
When they’re dry, pair the boards according to size. There will be three pairs total.
Choose any cover board. With a glue brush and glue, coat the back side of the board with a thin layer of glue.
Position the glued side of the board on the back of one decorative paper sheet.
Press the paper to the board and smooth out any air bubbles with the bone folder.
Use the scissors or craft knife to cut the extra decorative paper edges from the glued board.
Repeat these steps for each remaining cover board.
MAKE THE SIGNATURES To determine the dimensions of the pages for the journals, choose one of the cover boards and measure it. Write this measurement on a piece of scratch paper. Subtract 1/4 inch (6 mm) from the height. Multiply the width of the cover board side by two, and then subtract 1/4 inch (6 mm) from that total. For example, your paper size would be 73/4 x 43/4 inches (19.7 x 12 cm) if you had 4 x 5-inch (10.2 x 12.7 cm) covers.
With your paper cutter, cut 45 sheets of text-weight paper to this size. Separate the sheets into nine piles of five each. (There will be nine signatures in each journal.)
Use the bone folder to fold each stack into a signature.
Repeat steps 11 through 13 for each remaining set of covers.
CREATE A PUNCH GUIDE Determine the dimensions of the guide—it will be the same height as your signature and 2 inches (5.1 cm) wide. Cut the template from the sheet of cardstock to the determined size. Fold the template in half lengthwise, so it’s the same height as before and 1 inch (2.5 cm) wide. Smooth the crease with your bone folder.
Open the template and place it on your work surface.
Measure 1/2 inch (1.3 cm) from the top and bottom of the guide, and mark these points along the inside of the fold line.
Measure 1 inch (2.5 cm) from the top and bottom of the guide and mark these points along the inside of the fold line as well. You will have a total of four marks on the fold. Draw an arrow on the inside of the guide to signify the upright position. Tip: If your covers are more than 6 inches (15.2 cm) tall, you might consider adding more sewing stations in the center of the spine.
PUNCH THE HOLES IN THE SIGNATURES Nest the punch guides inside the corresponding signatures in the gutter of a phonebook and punch holes with your awl where you made marks. Repeat for each set of signatures. After completing each set of signatures, stack them and place them within their matching covers.
PUNCH THE HOLES IN THE COVER BOARDS Choose a book set to start with. Remove the top cover and the top signature. Place them on your work surface with the cover board on top of the signature and the spines facing you.
Center the signature under the cover board so there’s 1/8 inch (3 mm) of space at the top and bottom.
Slide the cover board back 1/4 inch (6 mm) or so to reveal the spine of the signature underneath it so you can use its holes as a guide.
Mark the placement of the holes on the cover board using a pencil. They should correspond to the top and bottom sewing stations on the signature. The two marks should be placed 1/4 inch (6 mm) from the spine edge of the board.
Use an awl to punch holes through the two marks.
Repeat steps 20 through 24 for the bottom board and all remaining cover boards.
ASSEMBLE THE BOOK Align the signatures within the two covers of one book, and place it on your work surface.
Determine the length of the binding thread by measuring the height of the signature. Multiply the height of the spine by nine and add 24 inches (61 cm). This is the amount of thread needed to sew each book.
Pull the bottom signature from the stack. Enter a threaded needle into the outside of the rightmost sewing station and pull it into the center of the signature. Pull the needle until there is a 12-inch (30.5 cm) tail of thread remaining on the outside of the signature. Enter the thread into the second sewing station and pull it to the outside of the signature. Continue sewing in running stitch with true kettle stitches linking the signatures at the top and bottom sewing stations. Variation: When you reach the final signature, you may wish to make a gathering stitch by looping around the previous running stitch threads. Complete the binding by linking the final sewing station to the previous signature with a true kettle stitch. Leave the thread long after the final stitch. It will be used to attach the covers.
Use the loose tail threads to attach the covers. Tie off the loose threads in the inside of the nearest signature and trim the tails to 1/4 inch (6 mm).
Repeat steps 24 through 29 for each journal set.