Automatic Pull Strip

Pop-Up

Posted by GMC Group

About

This mechanism uses a strip of card spanning the spine to raise a pop-up on the opposite page. The pop-up can be a Curved shape (as here), a flap, or a Parallelogram. The strip can be concealed beneath the page, which makes the effect even more surprising.

Share

You Will Need (1 thing)

  • Paperclips

Steps (29 steps, 30 minutes)

  1. 1

    First, take a piece of card approximately 4in (100mm) wide and 10in (254mm) long. Make folds for gluing-tabs at each end, and a third parallel fold about 1in (25mm) off centre. Length A plus one gluing-tab should be slightly less than one side of your card base. Length A should be longer than length B. 


  2. 2

    Use the width of a ruler to draw two horizontal, parallel guide lines (C and C).


  3. 3

    Draw the rest of the shape. The edges of tab D lie just within the guide lines. The edges of tabs E are just outside the guide lines. 


  4. 4

    Cut out the piece. The shape F to the left of the middle fold is an integral part of the strip; 
it guides the moving edge that slides on the page as the base opens. 


  5. 5

    Crease all the folds.


  6. 6

    Fold the main body of the piece over the strip.


  7. 7

    Fold tabs E underneath it. 


  8. 8

    Place the piece on the base with crease G not more than 1in (25mm) away from the spine. 


  9. 9

    Before gluing, try pulling tab D, to make sure that the strip can slide freely between tabs E. 


  10. 10

    With the whole piece in position, flat on the page, glue tabs E.


  11. 11

    Leave tab D flat on the page (NOT folded). Put glue on top of tab D, then close the base. Allow the glue to set before opening as tab D takes a lot of stress when the base is opened.

    Additions
    Additional flat strips can be added to this curved shape. Put glue on the end of the strips – they will rise at different angles, depending on where they are attached to the curve.

    Other pop-ups can also be built into the little gully created where the strip attaches to the base.

  12. 12

    Running the Automatic pull-strip under the page

    The strip can be constructed to run under the base. This holds the sliding part of the mechanism down on the page, it also hides the pull-strip and gets it out of the way of other pop-up constructions.

    In this variation the end of the pull-strip near the spine, A, is exactly the same as in the previous example, but the construction at the other end is slightly different – it has one long gluing-tab, B, all the way across the width of the piece.

  13. 13

    Two slits are cut in the base, C and C. Note the shape of these slits – their ends are extended horizontally by about 1⁄2in (13mm) to allow the page to lift slightly, and so facilitate the movement of the card.

  14. 14

    Construction: the strip is threaded through the slits until crease A is approximately 1⁄2in (13mm) from the spine; leave the gluing-tab lying flat.

  15. 15

    Fold the body of the card over towards the spine and fold tab B underneath it.

  16. 16

    With the piece lying flat, glue tab B to the page between the two slits.

  17. 17

    Put glue on top of tab A, then close the base and press firmly. Give the glue time to set before opening the page.

  18. 18

    Using the Automatic pull-strip to raise a flap in the middle of the page

    1 Make the flap – a piece of card with a gluing- tab on one side.

    2 Glue the flap to the page. Make two slits in the page – be sure to leave enough of a gap between slit A and the spine, and slit B and the flap for the pull-strip to be able to move comfortably.

    3 Draw a line, C, on the page parallel to the spine and about 1⁄2in (13mm) away from it. Draw a line, D, on the flap parallel to the
    crease where the flap is attached to the page. One end of the pull-strip will be attached here. The position of this line, D, is critical. To make the flap flip right over make length E = length F. To make the flap stand vertical make E = 2 x F. Measure the distance between the two lines, G.

    4 Make the pull-strip with a gluing-tab at
    each end. The distance between the gluing-tabs’ creases is G.

    5 Thread the pull-strip through the slots in the base.
    Glue one end of the pull-strip to the flap with the gluing-tab’s crease exactly on line D.

    Make sure the crease at the other end of the strip is exactly on line C then, with the gluing- tab flat, put glue on the top of it, shut the base and press firmly.

  19. 19

    Automatic pull-strip theory

    With the base closed this is the position of crease A in relation to the spine.

  20. 20

    With the base open, crease A moves to position B in relation to the spine. The distance between position A and position B is the amount of movement generated at the other end of the strip, C.

    At its most simple, this movement can be used to pull a flat image across the page. It can also be used to flip a flap, or raise a plane which can in turn lift Parallelograms or V-folds.

  21. 21

    A Parallelogram can be built onto the flap rising in the middle of the page

    Make a flap rise on the page as explained in 17.2. In this case at step 3, E will be 2 x F.

  22. 22

    Make a Parallelogram piece – length A will be the same height as the raised flap.

  23. 23

    Length B on the Parallelogram will be the same as the distance between the place where the flap’s crease is fixed to the page and where the Parallelogram glues down between
    the two slits in the base.

  24. 24

    Automatic pull-strip turning a flap on the opposite page

    This mechanism is made with two pieces. The first is
    a pull-strip with a gluing-tab, A, on one end and a flap on the other. There is a fold, B, between the flap and the strip.

  25. 25

    The second piece is a rectangle of card with a gluing-tab, C, in the middle of one edge. There is a crease between the gluing-tab and the card. Tab C will glue to the back of the flap. The other edge of the card, D, will glue down flat and flush against the edge of the base.

  26. 26

    Place the strip with A opened out flat and almost touching the spine of the base. Fold the flap over on top of the strip. Distance E between the spine and the crease of flap A must
    be the same as E between crease B and the crease of flap C.

  27. 27

    Glue the second piece into position with edge D flush
    against the edge of the page A and tab C glued to the back
    of the flap.

  28. 28

    Put glue on top of flap A. Close the base, press firmly and allow the glue on tab A to set.

  29. 29

    Open the base. Because the flap is folding towards the
    closing page it may need to be
    trimmed, as it will snag if it
    is too long.