About

Cost
$ $ $ $ $
Difficulty
• • • • •
Time
2h00

Dainty Jewelry Design-How to Make a Ring in Bloom Pattern
This blooming flower jewelry design is a great summer accessory and might just bring you lots of good luck, as is taught in the tradition of feng shui. Learn how to make a ring with this pattern in a few easy steps!

Published
Tags

PrintEmbed
  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 1
    Step 1

    Supplies needed for this jewelry design:

    3mm & 4mm Round Seed Bead (yellow)

    2mm Round Seed Bead (transparent)

    Acrylic Rhinestone Bead

    0.3mm Tiger Tail Wire

    Scissors

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 2
    Step 2

    Step 1: bead the flower pattern

    1. Form a loop with 5 pieces of 4mm yellow seed beads.

    2. On the left end for the wire, add on the beads as: 2mm transparent seed bead*1, acrylic rhinestone bead*1, 2mm transparent seed bead*1 and 4mm yellow seed bead; on the right one, add on the 3 beads besides last yellow piece as: 2mm transparent seed bead*1, acrylic rhinestone bead*1, 2mm transparent seed bead*1 (pay attention to the back and front side of acrylic rhinestone bead).

    3. Take the left working end to go through 3 beads on right end. Pull the wire tightly.

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 3
    Step 3

    4. Adjust the yellow seed bead loop upwards andfeed the upper working end through the adjacent seed bead.

    5. Next, continue to add beads on the two working ends. On the left end, add one 4mm yellow seed bead and one 2mm transparent piece; while on the right end, add on a 2mm seed bead and then an acrylic rhinestone bead.

    6. Lead the left end through the beads that are on right end. Tighten the wire.

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 4
    Step 4

    7. Repeat the steps 4 through 6 for the 3 other petals.

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 5
    Step 5

    8. At the end, you’ll need to add on beads on the two ends. Simply thread the left end through the adjoining 3 beads to meet the two ends at the backside of flower.

    9. Cross two ends through another 4mm yellow seed bead.

    10. String the 4mm yellow seed beads on backside with either end.

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 6
    Step 6

    Step 2: beaded ring band in jewelry design

    1. Once you have finished the flower part, exit the two working ends from two 2mm seed beads as the picture shows.

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 7
    Step 7

    2. Take 8 or so3mm yellow seed beads and then pass the two ends through all the beads together.

    3. Repeat the above process for the length needed to fit on your finger. Do not pull the wire too tightly.

    4. String one end through the opposite 3 seed beads from the flower. 5. Knot and secure the two ends firmly. Weave the remaining tails through several seed beads nearby and trim off the leftover wire.

  • How to make a gemstone ring. Dainty Jewelry Design How To Make A Ring In Bloom Pattern - Step 8
    Step 8

    Step 3: wear your ring

    The only thing left to do is to wear it and appreciate your own jewelry design!

    This chic, funky and youthful jewelry design is actually easy to make and can be whipped up in less than an hour. So if you’re searching for a design to match your outfits, this project on how to make a ring is a good way to make your own custom pieces.

Made this project? Share your version »

Comments

More Projects